Categories
Air Filters
Assortments & Refills
Backpack Sprayers
Bearings & Bushings
Belts
Carburetor Parts
Catalogs
Chainsaw Bars
Chainsaw Chain
Chainsaw Sprockets
Combos - Bar and Chain
Control Cables
Displays Drive Parts Edger Blades
Electrical Parts
Engine Parts
Fuel Cans & Accessories
Fuel Line / Accessories
Fuel Products Go-Kart Parts Grass Bags Ignition Parts
Kits for Chainsaw Bars
Lawnmower Blade Adapters Lawnmower Blade Maintenance Tools
Lawnmower Blades
Linkage, Jacks & Hardware Miscellaneous Parts Mufflers
Oil , Lubricants and Chemicals
Oil Filters
OREGON® Accessories
Personal Protective Equipment PowerSharp® Products
Pulleys
Saw Chain Packaging
Saw Chain Parts
Sculptor™ Bars Snowthrower Parts
Spark Plugs
Spindles
Starter Parts
Starter Rope
Starters
Steering Parts
Switches Tiller Tines
Tires/Tubes/Wheels
Tools Tools, Eyewear & Hearing Safety
Trimmer / Brushcutter Products
Trimmer Products
Wheel & Deck Accessories
Home Lawnmower Blades 396-703 BLADE, EXCEL GATOR™ G6™ 20 61/64 6PK
MADE IN THE USA
Oregon 396-703, BLADE,   EXCEL  GATOR™ G6™ 20 61/64 6PK
 
Part #396-703
 
$112.40 /ea
Quantity    
GATOR-G6.png
        
Want to upgrade Your Blade? Click Here!
 
BLADE DIMENSIONS Not Sure If It Fits? Click Here!
Length Center Outer C-to-C Width Thickness Offset Air Lift L-Cut
20-15/16 5/8 3.00 0.250 5/8 1-1/4
PRODUCT DESCRIPTION
Product InfoFeatures
Oregon 396-703, BLADE, EXCEL GATOR™ G6™ 20 61/64 6PK

Gator™ G6™ version of 96-703
GATOR™ G6™
Also Replaces:

HUSTLER: 782516

Product Code:396703
Oregon 396-703, BLADE, EXCEL GATOR™ G6™ 20 61/64 6PK
WARNING: Before servicing or removing blades
  • Remove and ground spark plug wire
  • Disconnect battery at negative terminal. (for electric start engines only)
  • Refer to owner’s manual and follow safety warnings
  • Do not substitute any other bolt for the blade retaining bolt. Blades and blade retaining bolts are specially made for this application.
  • Proper torque must be used when tightening the blade retaining bolt; refer to owner’s manual. If this safety precaution is not followed, the blade could come off during operation.
While mowing
  • Immediately inspect blade if abnormal vibration occurs
WARNING:
  • Properly support and secure mower when replacing blade.
  • To avoid possible injury, always wear proper eye and hand protection when servicing mower blade.
  • Unbalanced or warped blades can cause damage to the mower and/or personal injury.
  • Inspect the blade(s) and replace damaged blades before operating the mower
G3 G5 G6
DESIGNED
FOR SMALLER
ENGINE UNITS
AN OPTIMUM
COMBINATION FOR
A WIDE RANGE OF
MOWER UNITS
HEAVY-DUTY BLADES
DESIGNED TO WITHSTAND
PUNISHING CONIDTIONS
N/A
Click to View
N/A
Click to View
N/A
Click to View
HIGH-LIFT GATOR
MULCHER
X-TENDED
CUTTING
LENGTH
FUSION THICKER &
WIDER STEEL
STOCK
Superior
Bagging
Superior Side
Discharge
Superior
Mulching
Increased
Cutting
Preserves
Cutting Edge
Superior
Longevity
The aggressive blade angle increases
air flow to push debris up‑and‑out 
for superior bagging or side discharge.
Cleaner, more efficient cutting performance Up to twice
the cutting length for greater
efficiency
Tungsten carbide is “fused” to the blade, keeping your edge sharper, longer. Greater width and
thickness extends
blade life
IN FOUR SIMPLE STEPS
blademeasure_714x311.jpg
STEP 1 Measure the blade diagonally from cutting tip to cutting tip.
STEP 2 Measure the blade at the widest part of the blade.
STEP 3 Measure the center hole.
STEP 4 Measure the center to center distance between the outer holes.
 
FIND YOUR ARBOR HOLE TYPE

5 or 7 Point Star Center holes may be 5 or 7 point star shaped.

 

5-point Star 7-point Star

Square or Rectangular

The MTD built blades on many walk behind lawn mowers have a “bow-tie” hole. In this case the OREGON® replacement blade will have a rectangular center hole which will fit on the bow-tie pattern on the blade adapter.

 

Bow-tie Rectangular Bow‑tie/Rectangular

MTD Blades

The MTD® built blades (Bolens, Cub Cadet, Troy-Bilt, White, Yard Machine and Yardman) may have a 6 point star. OREGON® replacement blades will have a “Y” shaped center hole which will fit exactly on the 6 point star on the blade spindle.

 

6-point Star “Y” center hole 6-point Star
“Y” center hole

The two sizes of the 6 point star.

If your blade spindle has a bolt and lock washer that holds the blade to the machine you would use the 11/16” star or “Y” blade.

setupa.jpg

If your blade is secured with a large flange nut then you would use the 5/8” star or “Y” blade.

setupb.jpg